Відео

How Many Gauges And Colors Are The Low Voltage Wire ??? What Is The Name To Buy In Google ??? Amén.

Perfect. Have an old house with original valve stems. Fixed everything else from boiler to shower. Thanks 🙏🏼

Thank You, Papa

Was just quoted $2,600 parts & labor to replace my 2018 unit’s LG compressor.

Vine al lado gringo 👁️👄👁️

Hey! Great video. Liked and subscribed. I got 2 quotes $6000.00 & $8,000.00 to replace my A/C system. Was told the controller was toast. My system will run and cool, only issue is the fan stays on. Possible bad relay on controller? Anyway, I ordered a new control board for $150.00 and will swap it out. If it works, I guess I get to save at least $5,850.00. Thanks for posting this video and breaking down the one by one wire swap.

Thank you! Saved me a call to a locksmith

I just tried this on my Emerson microwave, and it worked right away. It's very strange that a cable like that would ever come loose. I'm wondering if disconnecting and reconnecting the ribbon cable is draining the panel of any residual power that might be causing the fault. Anyway, thanks for the quick fix!

Solution: my ac (independent) breaker was triping after 15min , I removed the breaker , there was a screw behind the switch which adjusted its sensitivity if I unscrew it , it was tripping easily , so I tightened it , then I attached it's all 4 wires in different way , by cleaning the ends and reshaping them just in case , tightened all 4 again , it stoped tripping ! . (turn off all the power supply 1st)

You are a life saver, I’m not sure of o was able to fix my problem but at least I was able to open that area. Thanks again!

Well done and succinct. Not all videos showed the key element of keeping the valve in the open position. This was the difference between success and failure with prior attempts.

Thank you❤

Wow das easy as hell

Very helpful 🎉

Do you post on reddit

Love you

I’m having same smell on mines I figured it’s this same problem I have whirlpool

Question, water heater is not elevated from the floor, it's basically flat inside the pan, if the pan get flooded, would it affect the pilot/flame area?

Why didnt you remove the air in your hoses? You're mixing air/moisture with refrigerant. Also - Why are you not measuring how much refrigerant you're recovering? I know the TARE says on the bottle but they're not 100% accurate

Thanks!! Took me 15mins to clear my garbage disposal after about 15hours of speculation lol

Ours was a bad, bad smell. I tried everything and finally found a fix. We emptied the entire fridge (to get the weight out, the wheels will gouge hardwood) pushed it out so we could access the back (compressor area). Took off the back cover (6 or 8 screws, very sharp panel) to expose all the dust. Vac that crap and it fixed our smell in about a day. We now vac the back every 1 1/2 years and no problems since.😉

This helped a lot fixed the problem thank you kind sir

Did this multiple times in a month. Even unplugged it for 3 days. Problem keeps happening.

Thank you for this! Saved me a lot of time trying to figure out what was happening. Never had the problem with previous washers so I had no clue what an air gap was.

Clear instructions 👍

I came to this video to know why water didn’t fill up but when I saw hat u can turn off the water I put my phone down and walked straight to the bathroom and when I turned it I heard it filling up man I was happy now knowing am a plumber now 😂

Thanks it was very helpfull

Thanks amigo very good video good explanation and clean long life to you amigo. I have fixed my wife washing machine tonight I not sleep in the couch.

Exactly what was wrong with mine. Works fine now. THANKS.

I hope mine are this easy to replace. I had a guy that was coming out today to do a rub surround, and he told me that the handle for the hot water wouldn't come off... so to not cause a massive leak he'll have to return after I get this taken care of. I'm trying not to have to pay for a plumber to come out to do something I might be able to do myself. I'll assess the situation and then decide if a plumber is needed. Thanks for the great content, direct and to the point. 👍🏻

I’ve been doing AC for 15 years and I always use my finger it’s plastic

Best video.

Thanks so much after watching your video I was able to close the garage door. The sensor was dirty. Thanks for the video.

People First, 1.Check Breaker With A Multimeter Both Side And Make Sure You Are Getting 240v, 2. Then Go To Contactor Continuity 3. 24v Contactor Amén.

Fantastic 💯💯💯

What's the point of the switch after the pressure switch?

Easy vid to follow. Thanks for this!

Thanks Sam!

I am wheelchair bound and whenever I encounter a problem in my atpartment, it makes it easier to call management knowing how easy the fix might be. Even if I can't do the repairs myself, this helps me stay knowledgeable. Thank you

Excellent. Thank you.

Thanks, nice explanation for beginners

All other videos suggest to replace the full thing, disconnect the water line. This is a cool approach…

This was one great tip! I never knew that I could remove the top off of the air gap. I used a piece of 1/4-inch irrigation tubing. I was ready to remove the black hose from under the sink. This was a time-saver. Thank you.

Nice explanation of issue that can caused the vibration, the fan blade pitch is important.

10/10. Haven't fixed my fan but gave me more information than just buy a balancing kit. I'm sure I can fix my vibration issue easily now

I wish you showed how you got it loose

awesome video! fixed my sink in a few minutes because of this video.

Hi Sam I have an Imperial Microwave with this problem what do I do to fix it

Thank you for the info. My keeps tripping the circuit brake, i went to buy it, but there's 2 options: a normally open and a normally close. Can you please tell me which one i need? Thank you.

This is a winner video style. Brief, good visuals, and narration. Plus I have the same unit.